USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models Review

Let’s Dive into USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models

The SIG SAUER P365 took the concealed carry world by storm, offering a near-perfect balance of capacity and concealability. The sear, a small but critical component within the P365’s fire control group, plays a crucial role in the pistol’s trigger pull and overall safety. We are examining a USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models. This used sear raises questions about value, reliability, and potential cost savings versus a new component.

As an experienced gunsmith and tactical gear specialist, I’m always looking for ways to optimize performance and reliability. The P365 has become a favorite among many for everyday carry. I was curious about the viability of using a used sear to possibly improve an older model P365 or even as a cost-effective spare part.

Upon receiving the used sear, my first impression was one of cautious optimism. It appeared intact, although showing signs of wear consistent with a used firearm component. Examining it under magnification revealed no immediately obvious cracks or deformities. This immediately made me more confident that this used part could possibly still be a viable component.

I considered purchasing a new sear but the cost savings of a used part, especially if it met my standards, was too tempting. Other options included aftermarket sears from Apex Tactical or Grey Guns, known for enhanced trigger performance. Ultimately, I chose the used SIG SAUER sear to maintain factory specifications, with the understanding that performance might be similar to stock but with the advantage of a lower price. I was cautiously excited, hoping it would be a worthwhile upgrade while acknowledging the risks associated with used firearm parts.

Check Best Price HERE

Real-World Testing: Putting USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models to the Test

First Use Experience

The true test of any firearm component is its performance under real-world conditions. I installed the USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models in a P365 that had seen approximately 2000 rounds. Initial testing was conducted at my local indoor range, focusing on trigger pull weight, creep, and overall smoothness. The range was a controlled environment which would allow for the most safe and accurate results.

The installation went smoothly, though I used extra caution, given the sear’s role in the firing mechanism. The initial trigger pull felt marginally lighter than the original sear. There were no immediate signs of malfunction, such as failure to reset or unexpected discharge.

However, after approximately 50 rounds, I noticed a slight inconsistency in trigger pull weight. There were no malfunctions, though this was a red flag considering the sear’s role in safety.

Extended Use & Reliability

After the initial range session, I subjected the USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models to further testing over several weeks. This included dry-firing drills, live-fire exercises at varying distances, and simulated concealed carry scenarios. It was also used during some outdoor range time in cooler weather. I needed to ensure the part was fully functional and safe.

After approximately 500 rounds, the initial inconsistency in trigger pull became more pronounced. The sear’s engagement with the striker seemed less predictable. It was time to remove the part.

Disappointingly, the used sear had not held up to extended use, exhibiting issues that could compromise reliability. The used part, while initially promising, proved to be a less reliable alternative than a new sear. This experience reinforced my belief that critical fire control components are best replaced with new parts.

Breaking Down the Features of USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models

Specifications

Unfortunately, the specifications for the USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models are limited due to its used nature. SIG SAUER doesn’t publish detailed specs for individual fire control parts available as spares. Key features for any P365 sear include proper hardening to prevent wear, precise geometry for reliable engagement, and compliance with SIG SAUER’s stringent safety standards.

Since it is used, the exact tolerance of this part would differ slightly from factory new. These parts are made of hardened steel. The finish would vary based on how much use it has seen.

Performance & Functionality

When functioning correctly, the sear ensures a safe and consistent trigger pull, reliable striker engagement, and proper reset. A worn or out-of-spec sear can lead to light strikes, inconsistent trigger weight, or even accidental discharge. My testing revealed that the USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models offered initially acceptable, though ultimately unreliable, performance.

The sear’s inconsistency was a significant weakness. Even though it was working, it was unreliable. It did not meet my expectations as a reliable fire control component.

Design & Ergonomics

The sear itself isn’t designed for ergonomics, but its proper function directly impacts the shooter’s experience. A smooth, consistent trigger pull enhances accuracy and control. The used sear offered a marginal improvement in initial pull weight, but the inconsistencies negated any benefit.

The component is small and easily installed by an experienced gunsmith. It requires minimal care, beyond ensuring proper lubrication.

Durability & Maintenance

The inherent risk of a used firearm part is unknown history and remaining service life. While the USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models appeared visually intact, its internal wear ultimately led to functional issues. Proper maintenance involves regular cleaning and inspection, but even with meticulous care, a used part will likely not last as long as a new one.

Maintenance is easy, but durability is questionable. The inconsistent performance is a major concern.

Accessories and Customization Options

The sear is a core component of the fire control group and not typically an area for external accessories. Customization options for the P365 generally focus on triggers, grip modules, and sights. While aftermarket sears are available from companies like Apex Tactical, these are designed for performance enhancement, not necessarily direct replacement of a used factory part.

A new sear could be paired with an aftermarket trigger, but this used sear is best used with a factory trigger. No other accessories are needed for the sear itself.

Pros and Cons of USED SIG SAUER P 365 Sear, KIT-365-SEAR, EDEMO1, – 1 out of 2 models