Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks Review

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks Made a Bold First Impression

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks isn’t going to win any beauty contests, but it promises a simple solution to a common problem: inadequate cheek weld on rifles utilizing Magpul‘s popular MOE and CTR stocks. This little piece of gray polymer aims to raise the shooter’s cheek by a quarter of an inch, potentially improving sight alignment and overall shooting comfort. It’s a straightforward accessory with a specific purpose, and at a price point hovering around ten bucks, it seemed like a worthwhile experiment.

I’ve always struggled with achieving a consistent cheek weld on my M1A Scout Squad, particularly when using lower-mounted optics. The factory stock provided a less-than-ideal interface, and I found myself straining to get a clear sight picture. I tried various makeshift solutions, from athletic tape to foam padding, but none were truly satisfactory. That’s when I started looking at dedicated cheek risers, and the Magpul offering caught my eye due to its simplicity and compatibility with the MOE stock adapter I already had installed on my M1A.

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks arrived in a small, unassuming package. Pulling it out, I was immediately struck by its lightweight and seemingly robust construction. The polymer felt solid, and the edges were clean and well-finished. Comparing it to other aftermarket cheek risers I’d seen (mostly bulky, adjustable models), the Magpul riser stood out for its minimalist design. I almost considered a larger, adjustable cheek riser system, but the simplicity and low profile of the Magpul ultimately won me over.

My initial impression was one of cautious optimism. It seemed like a well-made, no-nonsense accessory that could potentially solve my cheek weld issues. I was eager to install it and see if it lived up to its promise. I was slightly surprised by its relatively small size, but figured Magpul knew what they were doing.

Real-World Testing: Putting Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks to the Test

First Use Experience

My first range trip with the Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks was at my local outdoor range, under sunny skies and mild temperatures. I tested it on my M1A Scout Squad with a 2-7x32mm scout scope mounted forward of the receiver. Installation was a breeze – it simply clipped onto the existing MOE stock adapter, and felt secure from the get-go.

The difference in cheek weld was immediately noticeable. The quarter-inch rise provided just enough elevation to align my eye perfectly with the scope. I was no longer straining my neck or hunching over the rifle. This resulted in a much more natural and comfortable shooting position. It was easier to maintain a consistent sight picture, and I felt more confident in my shots.

After the first 20 rounds or so, the riser felt perfectly integrated into the rifle, and I hardly noticed it was there. There were no wobbles, shifts, or other annoying distractions. It felt solid and stable. However, I realized that, as advertised, this riser completely interferes with charging handle function on an AR-15.

Extended Use & Reliability

After several months of regular use, the Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks has held up remarkably well. The polymer has shown no signs of cracking, chipping, or fading, even after being exposed to the elements. It’s still as secure as the day I installed it, and there’s no play or movement whatsoever.

Cleaning is simple: a quick wipe with a damp cloth is usually all it takes to remove any dirt or grime. I haven’t had to perform any special maintenance or repairs. This is a huge contrast to my previous experience with the athletic tape method, which required frequent reapplication and left a sticky residue.

Overall, the Magpul riser has exceeded my expectations in terms of durability and reliability. It has consistently provided a comfortable and stable cheek weld, even during extended shooting sessions. It’s a simple yet effective accessory that has significantly improved my shooting experience with my M1A. It performs far better than my cobbled-together solutions of the past.

Breaking Down the Features of Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks

Specifications

• Product Name: Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks.
• Manufacturer: Magpul.
• Material: Polymer.
• Color: Gray.
• Height: 0.25 inches.
• Compatibility: Magpul MOE and CTR stocks.
• Origin: Made in the USA.
• Intended Use: Raises cheek weld for improved sight alignment.
• Important Note: Not compatible with AR-15/M4 platforms due to interference with the charging handle.

These specifications highlight the riser’s simple yet functional design. The polymer construction ensures durability and lightweight, while the 0.25-inch height provides a subtle but noticeable improvement in cheek weld. The compatibility with MOE and CTR stocks is crucial, and the explicit warning about AR-15/M4 incompatibility should be heeded.

Performance & Functionality

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks performs its job admirably. It effectively raises the shooter’s cheek, allowing for a more natural and comfortable head position when using optics. This leads to improved sight alignment, reduced eye strain, and ultimately, better accuracy.

Its strength lies in its simplicity. There are no adjustments to fiddle with, no screws to tighten, and no complicated installation procedures. It simply clips onto the stock and stays put. Its weakness, however, is that it is not adjustable. If a quarter-inch isn’t quite enough, or is too much, you’re out of luck. Overall, it meets expectations for a simple, affordable cheek riser.

Design & Ergonomics

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks features a minimalist design that blends seamlessly with the Magpul MOE and CTR stocks. The gray color is neutral and unobtrusive, and the smooth, rounded edges prevent snagging or discomfort. The polymer material is lightweight and durable.

It’s incredibly user-friendly. Installation takes seconds, and there’s no learning curve whatsoever. It’s a “set it and forget it” accessory that enhances the shooting experience without adding unnecessary complexity.

Durability & Maintenance

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks is built to last. The polymer construction is resistant to impacts, abrasions, and the elements. With reasonable care, it should provide years of reliable service.

Maintenance is a breeze. A quick wipe with a damp cloth is all that’s needed to keep it clean. There are no moving parts or intricate mechanisms to worry about.

Accessories and Customization Options

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks is a standalone accessory with limited customization options. It is designed to work specifically with Magpul MOE and CTR stocks and does not require any additional accessories.

While you can’t customize the height of this specific riser, Magpul does offer other cheek risers with different heights for more adjustability. The compatibility with MOE and CTR stocks opens up a world of possibilities for stock customization in general, including different colors, materials, and features.

Pros and Cons of Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks

Check Best Price HERE

Who Should Buy Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks?

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks is perfect for shooters who use Magpul MOE or CTR stocks on rifles other than AR-15/M4 types and need a slight increase in cheek weld for improved sight alignment with their optics. It’s ideal for those seeking a simple, affordable, and reliable solution without the bulk or complexity of adjustable cheek risers. This is particularly beneficial for M1A owners or those using similar platforms who want a more comfortable and consistent shooting experience.

This product should be skipped by AR-15/M4 owners (due to charging handle interference), or those who require a more significant or adjustable cheek weld. It’s also not necessary for those who are already satisfied with their existing stock and optic setup.

A must-have is a Magpul MOE or CTR stock (obviously). Otherwise, this riser is ready to go right out of the box.

Conclusion on Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks

The Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks is a testament to the power of simplicity. It’s a small, unassuming accessory that can make a big difference in shooting comfort and accuracy. It’s not flashy or feature-rich, but it does its job exceptionally well.

The price is more than justified. For around ten dollars, you get a durable, reliable, and easy-to-use cheek riser that can significantly improve your shooting experience.

I would wholeheartedly recommend the Magpul MOE/CTR Cheek Riser Gray 0.25″ fits MOE/CTR Stocks to anyone who fits the target demographic. If you’re struggling with cheek weld on your MOE or CTR-equipped rifle (again, not an AR-15), this is a no-brainer purchase. Don’t overthink it – just buy it and see the difference for yourself!

Check Best Price HERE