receiver

Forum Post Iver Johnson 20 ga by Joel
...rd the rear is stamped 28. Then a half inch further back is an E. A the front of te threaded portion of the receiver is a 5. Then midways of the threaded portion it appears to be 336 that is up side d...
Forum Post value german mauser by bigcurt
...ermany for another country,,possibly spain or a south american country,,is there anything on the top of the receiver ..like a crest orcoat of arms ?is the bolt numbered the same as the receiver?are th...
Forum Post 1890 value by 2bit
...good deal or not. The rifle was made in 1919 and is known as a Third Model of the 1890. The upper notched receiver is the major change from the previous versions. It looks all original and the wood...
Forum Post What would the value be for a Faberic Adearmas Oviedo bolt a... by bigcurt
...round 125-150,,it would bring more if all the numbers you mentioned matched or even if the bolt matched the receiver ,,be careful when the bolt serial number doesn't match the receiver for headsp...
Forum Post I just acquired a Winchester 94 .. .32 WS .. according to th... by 2bit
...l condition rifle either. One of the easiest points to notice is that the lever is the same color as the receiver. (See photo added at bottom of thread) When these rifle were made the receivers ...
Forum Post I received my great uncle's winchester model 94.It is in goo... by 2bit
...Poor record keeping during WW II. You say it has a rear peep sight. Is it mounted on the left side of the receiver or on the upper tang behind the hammer? My guess is the receiver. If it is, this ...
Forum Post Winchester Model 70 by bigcurt
...her words open the bolt and look inside the chamber ,,you shound see where the locking lugs engage into the receiver and the face of the chamber is where the bolt rests against the end of the barrel ...
Forum Post 1904 Winchester Model 1894, long barrel. by 2bit
...marks and bruises but still a fair amount of original finish across the wood. The wear of the wood and the receiver is consistent with each other. Redone wood that looks way too good for the metal i...
Forum Post Winchester Model 61 value. by 2bit
...nt sight whereas yours has a typical fron rifle sight. Most Winchester rifles have poorer bluing on the receiver than on the barrels. This is almost universal among them regardless of the model. ...
Forum Post Winchester model 92 by Craig Learn
...guessing the carbine is in fair to poor condition with all the blueing gone. The round 22" barrel and receiver are dull but I wouldn't call them rusted. I was expecting the serial number...
Forum Post Winchester 1873 Rifle with a standard or stationary sight I ... by 2bit
...ould have slid back during the opening of the lever so that spent shell could be ejected out the top of the receiver. That cover had to be manually closed when done firing. In addition, there shou...
Forum Post oviedo 7mm mauser by bigcurt
...with all matching numbers will bring the higher end numbers and rifles or short rifles with clear crests on receiver along with dates and arsenals eg (oviedo),,non import models can be found but mos...
Forum Post We have a single barrel, 12 gauge shotgun made by J. Stevens... by bigcurt
does it have a model number on it on the receiver it may be 107B instead of 1078,,in which case they were made from 1937-1958 and would value around 100 mabey a little more if extra clean,, bigcurt
Forum Post value and yr..for 94/30-30 by gunpowder1457
the receiver is pitted and i restored the stock-did i de-value this gun?
Forum Post Id of a M-1 garand by pcaru1
...etween 0 and 1 on a guage. Trigger is bedded but it locks up tight. Is the bedding an issue? It touches the receiver everywhere except a small gap (1mm) under the serial numbers on the very back of th...
Forum Post Marlin 99 (Revelation model120) by bonsaii boy
I have a Revelation that has a grooved receiver for scope but no bolt "hold back". Any idea what year it was made?
Forum Post Remington Model 12 by fpollard
Have this 22 and would like information on age and value. Octangonal barrel and receiver slightly distressed and pitted. Action works great. model number 216300
Forum Post value of ring on a 1894 winchester by 2bit
The saddle ring from the left side of the receiver? 2bit
Forum Post Winchester Rifle, Model 94 Value by bigcurt
...ill many many of these used today for deer hunting and it appeares your uncle did some hunting with it,,the receiver on these were a cast alloy and many i have seen are lacking in blue on the receiver...
Forum Post 1894 25-35 that wont feed by 2bit
Any chance you could take a photo looking down into the open receiver showing how high the shell gets. Try it without flash. 2bit
Forum Post How old is my Model 12 Winchester 16 Gauge???? by 2bit
...as used on the barrels since that is where the shell resides when it is dischrged or fired. The action, or receiver of the gun has different steel in it. These differences are the reason the bluing ...
Forum Post 1898 Springfield armory Krag by 5madfarmers
Serial 9910 would be a model 1892 - not 1898. Receiver should have "1894" on it.
Forum Post Remington 03-A3 by Kleist
...ally don't know these but I have one kinda like this.. Can you post more pictures up close of the receiver/ other park parts? .....
Forum Post 30-40 Krag, No.4 Mk I* - Long Branch dated 1944 by bigcurt
...are going up on enfields but some thing that effect the values would be matching serial numbers on bolt and receiver ,,serial numbers on stock matching receiver?,,mag matching numbers ? finish ?refini...
Forum Post Browning sweet 16 - Belgium Made by DMZER
Sweet 16 Belgium made, solid rib barrel, no designs on receiver, 85-90% of new look, 66734, any idea on value. respond here or call me at 912-271-7854 if interested.
Forum Post Winchester Mod 70 .270 manf. 1951 by Jim
What's the value of this rifle? It.s about 80%. Some ptting on the receiver, stock a bit rough too.
Forum Post Remmington 20 gage (2 1/4" max) Shotgun by bigcurt
what model is it ,,should be marked on the side of the receiver ,,pump,,, autoloader ??? bigcurt
Forum Post where is the serial number in a winchester 1897 model by bigcurt
i beleive there on the bottom of the receiver where you load the shells into the tube ,, bigcurt
Forum Post Blr .358 by Steelerzz
What is the value of BLR browning in .358 EC Japanese steel receiver?
Forum Post Egyptian M 1868 Remington Rolling Block Rifle by Joe Bering, Jr
...out proper ammo and a gunsmith's careful inspection of the rifle. The rifle has an unblued barrel and receiver and the metal retains silver coloration throughout but is without rust. The front ...
  << Back 1 2 3 4 [ 5 ] 6 7 8 9 10 11 12 13 14 ... 24 Next >>

The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 Gun Values Board