My Profile

Keep Up to Date:
Blog RSS
Blog
Forum RSS
Forum

receiver

... The barrel is marked '.22 Cal. Short Model CDM' and is SN 279XXX. There is a gate on the right side of the receiver to allow for loading/clearing the cylinder, with a pushrod stored under the barrel....
Can a full auto demilled receiver be reworked and rewelded into a semi-auto receiver?
...ure) on a 12 gauge side-by side shotgun manufactured by Liege Sporting Gun Company Ltd. Its engraved on the receiver area and on all of the exposed screw heads. It has twin triggers and the serial N...
I bought a Colt flattop upper receiver stamped with “C AF” for my H-BAR. It also has the number '4' stamped just above gas tube hole on the receiver. Can anybody tell me if this is a M4 re
...e with a Wnchester 94 and would like to put better sights on it. What are your experiences with the various receiver and tang sights by Lyman, Williams, and Marble's?...
... with serial #193341. It is stamped with eagle over N on frame next to serial #, and eagle over N on barrel receiver. Also on the receiver is a mark that looks like 66 with a red stag looking antler l...
...n a 12 gauge side-by side shotgun manufactured by Liege United Arms Co. Liege, Belgium. Its engraved on the receiver area and on all of the exposed screw heads. Its also labelled Ranger on the side. N...
... 1895 Savage lever action in 303 Sav. cal.? The rifling is good. The wood is good with fair finish and the receiver and barrel have some rust patches. It has a tang sight. Thanks...
I am restoring a 1903 Mark 1 Springfield. All the metal parts including the barrel action and receiver are in excellent condition. The only part I am replacing is the stock. I have real unboiled li
...one have anymore info on this shotgun. Has Genuine Armory Barrel stamped on top of barrel. Also stamped on receiver made in Charlotte NC. Thanks, Chief Thank You for your assistance...... P...
i need to know the value of a rifle.it is stamped 'carl gustafs stads gevarsfaktori 1913'on the receiver.Ive found several like guns,but nothing concrete.the barrel is rather short,but does not seem t
M1 Garand - 30.06, Springfield receiver, Beretta barrel $500 ammo available FN-49 (SAFN)8mm semi-auto, bayo, $400 ammo available SA-93 - Bulgarian AK, milled receiver, great trigger $450 30, 40 ro
...t after about 50 rounds it started sounding funny so I stopped shooting. Turns out the recoil buffer in the receiver had essentially fragmented. No, I was not shooting heavy loads (though I did want t...
...e your self, smelt the ore into Iron, convert the Iron into steel, make the hand tools to make the barrels, receiver, springs, hammer, firzen, etc. before you can build your rifle from scratch. Sinc...
How much values is added to an AR-15 that has a pre-ban receiver.
Is M1A1 using the same receiver as the M1 Garand? If there are any differences, what are they? With necessary modifications, is it possible to build an M1A1 using an existing Garand rifle? What is a g
I am looking for information on where to find a Williams or Parker Hale receiver site for a Martini-Henry Cadet rifle. The Parker Hale #7 fits it, but I can not find one anywhere.(If any one has a PH
...e after about 25 rounds so I just quit and went home. The next day I found that the barrel was loose in the receiver and I could very easily move it around and rotate it. Was I in any danger? The guns...
...hvesk in very good shape, 12-port muzzlebreak, standard stock, all matching numbers except for the mag. The receiver is grooved for a scope but doesn't have the cutout on top that some do. Bore is ver...
...s soft steel in its guns. Where else would I look for a wide-body high capacity 1911, or even just the wide receiver to build one on? Is STI the only game in town? I ask because I like hi-cap, but...
i am a wanna be machinist and an hoby gunsmith. i have machined 3 AR15 lower receivers and built them all up to complete rifles. two of the guns have A2 stocks and the third has a fixed telescoping st
...ngs, burrs, or roughs. The barrel is counterbored slightly, and bluing is medium dark on a good polish. The receiver finish is not as good, but still a very acceptable matte, brush, and polished mixtu...
...or con on the various .50 BMG uppers for the AR rifle. Any reports of lower failure or stress cracks in the receiver?...
...elp me out. I have a Marlin 39A (New) on order and will pick up in a few days. My intent was to buy a Lyman receiver peep sight for it. I recently saw a post on Marlins forum where the poster said tha...
I bought a new DPMS complete upper receiver, carbine with A2 sight system , to put on my Bushmaster Varminter. The rear sights after zero set are left of center line 1/3 of the way, and the rear assem
...he gun ban seems to be so general that I am lost completely in the issue. The question is can I have a AK47 receiver imported to the US? I am not talking about building a rifle, just the importation o...
I just bought a new .22 Cal Ruger Mk2 target pistol (5.5 inch bull barrel, mk512). I notice that the barrel/receiver has some play in it's attachment to the to the pistol handle. I feel some play and
...barrel accessory program. You send them everything but your barrel then they fit your new barrel to the old receiver. Now here in lies the question when i get the gun back from them can i interchange ...
If i leave a spent round in the receiver for a week or so it will not eject when i go to load a fresh round to fire it. Any suggestions as to why and how to stop it? Forgot to say we are talking 22LR.
...tain Hill, Grim said. Grim, who ruled the death an accident, said the malfunction happened in the rifle's receiver ring. Neighbors learned of deRuiter's death Sunday night. ''Everyone is in tota...
...eated to 450 degrees or above. If I used a small torch, would this much heat damage or make the shotgun's receiver unsafe....
Hi there Funny thing, I called ColtMFG. And they told me they don't sell lowers.??? Kinda leaves me hanging. So where do you get one.
...amateur to assemble an FN-FAL type rifle with hand tools only? I read somewhere the barrel is fitted to the receiver with washers to control headspace. Does that mean no lathe is required. I'm wonderi...
...will be putting the box magazine back in. My question: Which side of the box magazine goes up (toward the receiver)? I thought I'd remember just by looking at it, but now I'm not so sure. I'd probab...
Hello, I am looking to purchase 2 AR-15 PRE BAN stripped lower receivers I will be using RRA (Rock River) uppers on them either Elite LE Tactical Car A2's. Please contact me, if you have anything,
Where can I get a complete lower receiver for an AR-15 whilst avoiding FFL?
Page: 1

Copyright © 2006 - Dec 2008 Gun Values Board