parts
...r between,,rebuild carbines if not import stamped can range from 500-800.. at some point underwood used parts from just about all the major manufactures and some parts may be stamped unquality which...
Anyone know approx value range in Fair Condition. All working parts, just age and normal "working" wear.
...I want to do that same thing and try and find another "beat up" one at a gun show and swap the parts over.
-Seth...
You might give Numrich gun parts a try; their e-mail address is egunparts.com. Hope this helps
...me brewed model,,any markings on the barrels,,parker shotguns were high quality shotguns and alot of the parts were handfitted to exacting detail,,doesn't sound like your average run of the mill ...
hello,,trade name bolt action shotguns seem to be in the 100-150 range around my parts ,,good starter guns for youths ..
bigcurt
I would like to know approximate value of a double dated German Lugar 1920/1921 all matching parts except mag. sn is 2390 model P08 w/ holster approx 85 % condition
hello,,the 922 h+r's seem to be bringing around 125-175 around my parts these days sometimes as high as 200 if really clean with box,,
bigcurt
Numerich Gun Parts has many schematics for guns both old & new. You might find something there you find useful.
...steyr inspectors proofed after the rifle was assembled ,,the germans had strict quality control and most parts on ww2 german rifles will bear german inspection proofs ,,if your stock is the original f...
I believe this is a commercial barreled receiver utilizing military issue parts.
I think the range on this is $250-$400..
..
i have a 20 gage ranger model 30 pump with 28inch barrel and adjustable choke where can i get parts for it ?
...,,i don't beleive the were sold with bayos though,,first off you should check the rifle for correct parts ,,most parts should have a R for remington stamped on them ,,bolt ,saftey,cutoff lever,,b...
the parts all match and are original,good solid gun but the blueing is worn will the value decrease if i have it reblued?
...eck here and look at the cross refrence link and see if it's listed there and then see if they have parts for your model,,also if you don't find it in the cross refrence section check the sa...
How much does it cost for the parts to convert my HK SL8 to take M-16 magazines? And is it a hard conversion?
...and i've seen some guys asking as high as 1000 depending on the rifle and overall condition and the parts put on them ..
,, i have a friend who collected 1903 springfields and saw him spend a ...
Value of double dated P08 German Lugar 1920/1921 SN 2390 matching sn on all parts except the mag. also have holster and the gun is approx 85%
check out this site for parts.
http://www.e-gunparts.com/productschem.asp?
chrMasterModel=0950z50
Kim
...l,,so with all the above in mind i'd say your colt may be worth around a couple hundresd bucks as a parts gun for someone needing internal parts or as a shooter if somebody doesn't care abou...
...w2 war years the models was changed to the 1903a3 which was a faster model to manufacture because milled parts were replaced with stamped parts and the rear sites were changed from barrel mounted rear...
...hat is the value of a German Baretta 9mm Model 2611 with the serial # 1915 with the No. 11 on all of its parts?...
Jeff,
You might try looking at this link.
http://www.winchesterguns.com/customerservice/
partsservice/obsolete-parts.asp
Good luck
2bit
... one as well, 1929 Model. Let me know if you want to sell it. The ejector on my broke and I need a "parts" model. Email me at lazlom@hotmail.com ...
...tring fireing proof for acceptance,, being it's a remington it should have mostly remington marked parts,,these will have a small R stamped somewhere on them and will include the bolt,the saftey...
...e of a Remington Fieldmaster 121, manufacture date Nov. 1951. It is in good condition. No rust on metal parts, slide action works smoothly. Wood stock has some nicks and scratches. I bought the rifle...
i have a pistol with swatiscas on it and matching numbers on all three parts. kinda brown, think is a browning 9mm from war..any idea of value? thanks
hello,,i asume your talking about a ithica md 37 pumpgun,,around my parts i see them in the 250-300 range..
bigcurt
...gton 66's have really took a jump in value in the last couple years and in g-vg condition around my parts there bringing 200-300..
bigcurt...
... a Winchester Mod 94, SRC in good condition, (I think so) The rifle has tang peep sighting. All Original parts to the best of my knowledge.
Serial 894XXX
Manufacture Date 1921
I know that it ha...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 Gun Values Board |
TIP: Write your question in details [ why? ]
Latest Posts
|
more posts...